- #Antares vending machine key install#
- #Antares vending machine key manual#
- #Antares vending machine key full#
I s engaged when the value of the grinder Replace the grinders.
The display shows the Reset the decounter is equivalent to zero. Memorized signals Undertake to fill the container Is engaged if the programmed grinder time out is engaged. This alarm is only engaged if the Executive or Mdb c oi n box i s e nga ge d. On engaging the reset mes sage the missing Undertake alarm reset. Before undertaking any operations on the machine ensure that the distributor power supply is disconnected. NOTE: so as to cancel a test pre-selection without dispensing drinks it is sufficient to press the service key inside the door again. This operation is to be undertaken with the machine on, and therefore is only permitted to the technical staff authorized to carry out such operations. ANTARES Before connecting the power supply, ensure that the distributor has been connected to the water mains and that the water tap has been turned on. Each regulation operation is the exclusive responsibility of the installation technician who also holds the. The installation technician is defined as the person responsible for the installation of the automatic distributor. In the event of a fault the maintenance technician must call the installation technician. The maintenance technician is also responsible for cleaning the distributor see operations indicated in.
The maintenance technician is defined as being the person responsible for filling up the containers with. In the event of a fault the user is obliged to notify the maintenance technician or the person responsible. The user is not allowed to undertake any maintenance operations either ordinary or extraordinary. The user is defined as the person authorized to collect drinks from the automatic distributor.
#Antares vending machine key manual#
READ the instruction manual machine carefully before using the machine. If you're unsure of the actual operating pressure then bleed some gas off and see if you have any change.Page of 54 Go. That is the highest pressure I can get on the low side of those units regardless of the amount of gas I put in. If you have a gauge set then put your blue low side line on the line tap while the unit is running and see what the pressure is.Īs I said, the low side should run around lbs. Not only am I interested in this specific machine but general info about refrigerators and freezers in general. Some say that if the suction line is frosted the entire way to the compressor that means the system is overcharged. Hoping someone has a Anteres combo with a charging tag still attached that they can varify the charge weight. It held the vaccuum for 1 hour so I figured if it was leakind it was not a huge leak and was worth trying to recharge. But given the choice I figured I could not go wrong filling it via the factory specified charge weight. I am familiar with the idea of filling a system via pressure only. Yes, I peirced into the low side what I refer to as the suction side.
#Antares vending machine key full#
I have a full gauge set that I use for auto AC work. When it craps out you just scrap it and buy another or a paltry sum. I'm glad you recognize that the machine has no value. It's just a matter of time before it leaks out again and you have warm soda. Live large while it's cold because these things leak the gas out inside the cabinet walls where you can't repair the leaks. My guess is it's overcharged, but it doesn't matter since your machine is now cold. Without gauges there is no way to know if it's now overcharged or still undercharged and the iced line is a symptom of that. I always add gas until I get to around lbs on the low side when the unit is running. I don't even know if you tapped the low side or not.
You are supposed to use refrigeration gauges to watch the low side pressure as you add gas.
#Antares vending machine key install#
Perhaps the suction line is supposed to be fully frosted all the way up to the compressor, can anyone give me some insight? You would not install a full load of freon unless you evacuated the system first, so it doesn't matter how much the factory put in it. The machine is cooling well now, my only concern is the suction line is frosting up heavily now and I want to make sure the issue is not with the amount of refrigerant that I put in. I got this number from a photo that I found of a tag that I think was of an Edina machine. I can not find a tag to tell me the correct amount of Ra to put in the unit only a label on the compressor specifiying Ra. I have an Antares Combo built around the notorious Edina upright freezer converted into a refrigerator. Barbecue Food Trucks.By mg81May 20, in Beverage and Food Vending. Corn Roasting Trailers.īeverage and Coffee Trailers.
0 kommentar(er)
